Skip to content
Flooring Guide · 22 Minute Read

Tile Flooring, Explained

What tile is made of, what its labels mean, how water and the floor underneath affect it, and how to care for it. We explain it the way we do in our Bolton showroom.

To see products, browse our tile collection, or price your rooms in the installation calculator.

Written by The Flooring Mart Inc. · Published · Last updated

Start here

What is tile flooring, and what should I check before I choose it?

The short answer

Tile is a hard floor made of clay baked in a kiln (ceramic or porcelain) or of natural stone. Each tile is stuck to the floor with mortar, and the gaps between tiles are filled with grout. Porcelain is a dense kind of ceramic tile that soaks up very little water. Before you choose, do three things. Check that the tile’s maker approves it for floors. Read its wear and slip information. And make sure the floor underneath is ready. Tile and grout do not stop water on their own, so a shower needs a complete waterproofing system.

Who this guide helps

Homeowners choosing floor tile for an entry, kitchen, bathroom, laundry room or basement. Also anyone comparing porcelain, ceramic and natural stone, or planning tile over in-floor heating.

The basics

What is tile made of?

Most floor tile is ceramic: clay and minerals pressed into shape and baked in a kiln. Porcelain is a kind of ceramic tile that is denser and soaks up very little water. Natural stone, such as marble or slate, is cut from rock and is a separate family with its own care.

Porcelain and ceramic

In North America, porcelain is defined by a test, not by how hot the kiln was. A porcelain tile soaks up 0.5% water or less in a standard test (ASTM C373). Tile that soaks up more is called non-porcelain ceramic, or simply ceramic.

Some tile sold as porcelain does not meet that standard. Tiles certified by the Porcelain Tile Certification Agency carry its mark. For any other tile, check the water absorption figure on the maker’s data sheet.

A tile on its own, and the layers of a tiled floor Two drawings, one above the other. Above: one tile on its own, cut across — the tile body, with a glaze on top on a glazed tile. Below: part of a finished tiled floor, cut across — two tiles with a grout joint between them, a layer of mortar under the tiles, a membrane under the mortar that some floors need, and the subfloor or concrete slab at the bottom. The lower drawing is one example only: which layers a floor needs depends on the tile, the floor underneath and the room. THE TILEA TILED FLOOR — ONE EXAMPLE GlazeOn glazed tile only Tile bodyThe surface, if unglazed Grout joint Tile MortarBonds the tile MembraneSome floors need one Subfloor or slabSound, flat and stiff
Above: one tile on its own. A glazed tile has a glass-like coat on its body; on an unglazed tile the body is the surface. Below: part of a finished floor, drawn as one example. The tile is bonded to the floor with mortar, and grout fills the joints between tiles. Some floors need a membrane under the mortar. It can waterproof a wet area, or let the floor and the tile move a little on their own. The subfloor or concrete slab has to be sound, flat and stiff enough. Which layers a floor needs depends on the tile, the floor underneath and the room.
Three families of tile. Every row depends on the product, so check its maker’s data.
PorcelainCeramic (non-porcelain)Natural stone
Made fromClay and minerals, pressed dense and bakedClay and minerals, baked; usually glazedRock cut into tiles, such as marble, limestone, travertine or slate
Water it soaks up0.5% or less: that is the definitionMore than 0.5%Depends on the stone
Outdoors or unheated roomsOften frost-resistant, but only where its maker rates itOnly where its maker rates itOnly where it is rated for it
Cutting and settingHarder to cut; the mortar is chosen to suit itEasier to cut and to bondNeeds full mortar contact and a stiffer floor
SealingOrdinary glazed: none. Unglazed or polished: as its maker saysOrdinary glazed: none. Unglazed, such as quarry tile: as its maker saysSome stones benefit from a sealer; many do not

Glazed and unglazed

A glazed tile has a glass-like coat baked onto its surface, and the coat carries the colour and pattern. Glazed tile is usually a little easier to keep clean. An unglazed tile has no coat: its body is the surface, and it may grip better underfoot.

In through-body porcelain, the colour runs right through the tile, so wear and chips show less. Coloured-body porcelain is usually glazed, and its body is coloured to match the surface. So a chip shows less on it than on a plain-bodied glazed tile.

Finishes

A polished finish is shiny and smooth. Polishing opens tiny pores in the surface. So polished porcelain can show fine scratches and stains more easily. A polished floor belongs where it stays dry when people walk on it, unless its maker says otherwise. A matte finish has no shine. A textured finish adds grip and can take more effort to clean.

Edges, sizes and mosaics

Rectified tiles have their edges ground after baking, so every tile is very close to its stated size, which allows narrower grout lines. Calibrated tiles are sorted into size ranges and need slightly wider joints.

Mosaics are small tiles, usually supplied on sheets of mesh or paper. In the tile standard, ceramic mosaic tiles are pieces under 9 square inches. Some mosaics, such as stone brick and herringbone sheets, use larger pieces. More joints mean more grout to keep clean.

There is no single definition of “large-format” tile. What matters is this. Once any side of a tile is 15 inches or longer, the installation standard asks for a flatter floor (see the floor underneath).

Our rangeMost of the floor tile we carry is porcelain: glazed, unglazed and coloured-body. We also carry mosaics, some ceramic tile and some natural marble. This guide also explains kinds of tile we do not carry, so you can read any tile’s labels. Browse our tile collection.
Ratings and labels

What do a tile’s labels and ratings tell me?

A tile’s look cannot tell you whether it suits a floor. Its maker’s data can. It can tell you where the tile may be used and how much water it soaks up. It can also tell you how its surface wears, how it grips when wet, and how much its colour varies.

What each label measures, and what it does not
LabelWhat it tells youWhat it does not tell you
Approved useWhere the maker approves the tile: floors and walls or walls only, indoors or outdoorsHow it wears, grips or handles frost: check those separately
Water absorptionHow much water the tile body soaks up: impervious (0.5% or less, porcelain), vitreous (over 0.5% to 3%), semi-vitreous (over 3% to 7%), non-vitreous (over 7%)Whether the floor or the room is protected from water: that is the installation’s job
PEI class (ASTM C1027)A wear rating for glazed tile: how well its surface resists visible wear, from Class 0 (walls only) up to Class 5; each maker words its classes a little differentlyUnglazed tile (it is tested another way), scratches, slip resistance, water or frost
Slip class and DCOF (ANSI A326.3)How the surface grips in a standard lab test (DCOF is that measure of grip), and the kind of area its maker says it suits, such as Interior WetWhether a person will slip: shoes, water, oil, dirt and slopes all matter
European tests (ISO 10545, DIN “R” slip classes)Results of European test methods, which many tiles list, such as a slip class of R9 or R10How they compare with the North American tests above: they are different tests, so ask what a rating means for your room
Frost resistance (ASTM C1026)Whether the tile passed a freeze-and-thaw testWhether a whole outdoor floor will last: water in the joints or under the tile can still do damage
Shade variation (V1 to V4)How much colour and pattern vary from tile to tile: V1 is uniform, V4 varies a lotWhich tiles you will get: view several pieces and blend boxes
Rectified or calibratedHow exact the tile’s size is, which sets how narrow the grout joints can beHow flat the tile is, or how it wears

Slip resistance in plain words

Slip resistance is not one number. The lab figure is called DCOF (dynamic coefficient of friction). It compares surfaces under set conditions. The standard itself says it does not predict whether a person will slip. Some level indoor floors are walked on when they are wet with water. For these, the North American standard (ANSI A326.3) asks for a wet DCOF of 0.42 or more, unless the maker says otherwise. Makers also place floor tile in classes: Interior Dry, Interior Wet, Interior Wet Plus, Exterior Wet, and Oils and Greases.

No tile is slip-proof. Tile below 0.42 when wet, such as polished tile, belongs where the floor stays dry, unless its maker says otherwise. No single number covers showers, ramps, outdoor floors or bare feet. Grip can also change as a floor wears or gets dirty.

On our tile pagesOur tile pages list the approved use: floors and walls, or walls only. Where the maker publishes them, they also list the shade variation and the abrasion and slip ratings. Many of the tiles we carry are tested to European standards, such as ISO 10545 and the DIN “R” slip classes (R9, R10 and so on). These are different tests from the North American ones explained here. Where a maker has published no figure, the page says “Not specified”. Ask our team what a rating means for your room, or for a missing figure, and we will request it.
Where tile fits

Which rooms suit tile?

Tile suits most rooms when the tile is rated for the floor and the room, and the floor underneath is sound. The table shows what to check in each.

What to check, room by room
RoomWhat to check
Entrance and mudroomA slip rating for floors that get wet, a hard-wearing surface (for glazed tile, a higher PEI class), and mats to catch grit and water.
KitchenA slip rating for floors that get wet. Glazed tile wipes clean; polished tile needs more care.
Bathroom floorA slip rating for wet floors, such as an Interior Wet class or the maker’s approval. Waterproofing under the tile is an option to choose. A shower is different: see tile and water.
Laundry roomA slip rating for wet floors, and a plan for leaks: tile and grout do not stop water reaching the floor underneath.
BasementThe concrete: its cracks and its moisture. Moisture from the ground can move up through a slab, so the slab is checked before tiling.
CondoYour building’s rules decide. Some buildings require approval and a sound-reducing layer under tile; ask your management before you buy.
Over in-floor heatingA tile its maker allows over heating, and a heating system, setting materials and any membrane used together as their makers instruct.
Outdoors, a garage or an unheated roomA tile its maker rates for outdoor or freezing conditions, and an installation built for them.

Busy households, pets and children

Good to know
  • Through-body porcelain shows wear and chips less; for glazed tile, the PEI class tells you how its surface resists wear
  • Glazed tile is usually easy to wipe clean, and mats at the doors catch grit
  • Tile is hard and can feel cool to the touch; rugs help, and in-floor heating can warm it

Before you choose

Check
  • The approved use and slip rating for each room
  • For glazed tile, the abrasion (PEI) class
  • The floor underneath: flat, stiff and dry enough

To see tile in a finished home, look at our Caledon East project, where a marble-look tile entry meets new solid hardwood.

Water

Is a tile floor waterproof?

Not on its own. Porcelain soaks up very little water, but grout joints let water through. Protecting the floor underneath is the job of the installation and, where it is needed, a waterproofing membrane.

Five parts of a tiled floor, five different jobs
PartWhat it does with water
The tilePorcelain soaks up 0.5% or less; other ceramic tile and many stones soak up more.
The grout and jointsFill the gaps between tiles. Grout is not a waterproof layer.
The floor underneathWater that gets through can reach the subfloor or slab, and a slab can also carry moisture up from the ground.
A waterproofing membraneA layer bonded under the tile that stops water. The North American standard for these is ANSI A118.10; whether a product meets it depends on the product.
The whole installationSlope to a drain where one is needed, sealed seams and corners, movement joints, and one maker’s tested system working together.

A bathroom floor is not a shower

The tile industry treats a bathroom floor as a limited-water area. Water arrives now and then and is wiped up. Waterproofing under the tile is an option. If you want it, it has to be chosen and written into the plan. A shower floor and its walls are wet areas. They are built as one system that slopes to a drain. A waterproofing membrane, or a similar tested system, sits behind the tile.

Have a shower, a wet room, a past leak or a floor that flexes checked in person. A floor that flexes is made stiff enough first. For a shower or a wet room, use one maker’s complete waterproofing system. Mixing products from different systems risks leaks and can void the warranty. Our calculator prices a waterproofing membrane under floor tile as its own line. Showers are planned as part of a bathroom renovation.

Installation

What does a tile floor need underneath?

Tile is only as good as the floor it is stuck to. That floor has to be sound and flat enough for the tile. It must be stiff enough not to bend too much, and ready for the setting materials the tile needs.

Flat is not the same as level

Flat means no humps or dips. Level means horizontal. Tile needs a flat floor; making a floor level as well can cost far more. Mortar is not used to flatten a floor: high spots are ground down and low spots are filled first.

Bigger tiles need a flatter floor. The Ceramic Tile Education Foundation explains the North American installation standard (ANSI A108.02) this way. Under tiles with every side shorter than 15 inches, the floor may vary by up to 1/4 inch over 10 feet. Once any side is 15 inches or longer, the limit is 1/8 inch over 10 feet. That is why large tiles often need more floor preparation.

Stiff enough

A wood floor that bends too much as people walk on it can crack grout and tiles. For ceramic and porcelain, the traditional figure is this: the floor may bend by no more than its span divided by 360. The span is the distance between the floor’s supports. Natural stone needs a stiffer floor. In practice, installers rely on tested floor build-ups rather than one number. These sometimes add a layer of plywood or a cement backer board, a stiff board laid over the subfloor.

Concrete, cracks and movement

Tile bonded to concrete moves with it, so cracks and joints in the slab can come through the tile. Joints in the slab are carried up through the tile. Cracks are checked. Where the membrane’s maker allows, a small crack can be bridged with a crack-isolation membrane, which stops the crack from passing up into the tile. New concrete also needs time to cure before tiling.

Every tile floor needs room to move. In a small room, a gap around the edge, hidden by the baseboard, can be enough. Larger floors, sunny spots and damp areas also need flexible joints within the tile. Where they go is planned for each floor, and they are filled with a flexible sealant, not grout.

Mortar, grout and layout

Tile is set in a mortar chosen for the tile, the floor underneath and the system. Examples are a cement mortar with added polymers for porcelain, or a mortar made for large and heavy tiles. Wet areas and outdoor floors need fuller mortar contact under each tile than dry indoor floors. The two main kinds of grout are cement-based and epoxy. Epoxy grout is harder and nearly stain-proof. Your installer matches the mortar and grout to the tile; there is no single recipe.

When long tiles are laid in a staggered pattern, each row is usually offset by no more than a third of the tile’s length, unless the maker allows more. A half offset can make the slight natural bow of long tiles show: their edges stand up from their neighbours, which is called lippage. Grout joints are sized to the tiles too: rectified tiles can take narrower joints than calibrated ones.

Membranes and in-floor heating

An uncoupling membrane is a thin sheet between the floor and the tile. It lets them move slightly on their own, so stress in the floor is not passed straight into the tile. Some also waterproof when their seams are sealed. A membrane does not make up for a floor that bends too much, and it does not replace movement joints.

Tile can go over electric or hot-water floor heating. The heating system, the setting materials and any membrane must be used together as their makers instruct, and the tile’s maker must allow it. One heating-cable maker’s instructions we reviewed call for the electrical work to meet the Canadian Electrical Code. They also call for the heat to stay off until the mortar has fully cured.

Tile over an existing floor

Tile can go over some existing floors, but only where the mortar maker approves it and everything underneath is sound. Examples are well-bonded old tile with the right preparation, or one well-attached layer of sheet vinyl without a cushion back. Cushion-backed vinyl is not a base for tile, and leftover carpet glue is removed first. Every layer raises the floor, so doorways, appliances and transitions to other floors are checked too.

In an older home, have old floor tiles tested for asbestos before they are taken up or sanded.

Who installs itInstallation is completed by The Flooring Mart’s own in-house installation teams. We do not use subcontractors, which is why we can stand behind our flooring installation work with a 2-year limited workmanship warranty.
Care

How do I look after a tile floor?

Sweep or vacuum grit, and wash with a cleaner the tile and grout makers approve, then rinse it off. Never use an acid cleaner on cement grout or on marble, limestone or travertine.

Sealing, by type: follow the maker of each material
SurfaceDoes it need a sealer?
Ordinary glazed tileNo. Do not coat the glaze.
Polished porcelain, glazed or unglazedFollow the tile maker; one maker recommends a penetrating sealer before it is grouted.
Unglazed tile, such as unglazed porcelain or quarry tileSometimes: follow the tile maker.
Natural stoneSome stones benefit from a sealer and many do not. A sealer makes stone more stain-resistant, not stain-proof; ask which product to use and how often.
Cement groutFollow the grout maker: some recommend a sealer, others say none is needed.
Epoxy groutNot normally sealed; it is nearly stain-proof.

A cleaner that is not rinsed off can leave a film that makes a floor more slippery. Oil- or wax-based soaps leave a film in grout. Grout still needs cleaning now and then, sealed or not.

Stone needs gentler care

Marble, limestone, travertine and onyx are sensitive to acids: lemon, vinegar and acidic cleaners can dull or etch them. Clean stone with a neutral cleaner, a stone soap or a mild dish detergent, rinse it, and avoid scouring powders.

Cracks, chips and repairs

A cracked or chipped tile can be cut out and replaced. Find the cause first, such as a floor that bends, missing movement joints or poor mortar contact, or the repair may not last. For cracked grout, TCNA advises raking out at least two-thirds of the old grout’s depth before new grout goes in.

Keep spare tiles from the same order, with their box labels. A later batch can be slightly lighter or darker.

Costs

What does a tile floor cost?

A tile floor costs more than the tile. Its size, its pattern, the floor underneath and what the room needs, such as a membrane, heating or trims, all change the price.

What goes into a tile price. Our figures are read from the calculator when this page is published.
Part of the priceWhat changes itOur prices
TileThe material and its size; in our range, natural stone and marble mosaics cost the most per square footFrom $2.99 per sq ft
Installation of standard floor tileIncludes mortar, wire mesh, levelling clips, grout, levellers and spacers.From $15.00 per sq ft, with a minimum installation charge, from $1,250.00
Mosaic, subway, wall, shower and patterned workMore cutting, more joints and more planningQuoted for each project
Taking up old tileIncludes the wire mesh, adhesive and basic preparation$3.65 per sq ft, then disposal at $0.75 per sq ft, or a bin on site instead, from $350.00
Floor preparationGrinding, patching, levelling, an extra layer of plywood, crack isolationPriced once we see the floor
Waterproofing membrane under floor tileWhere you choose one, such as a bathroom or laundry floor$1.50 per sq ft
Uncoupling membrane, in-floor heatingChosen for the floor and the roomQuoted for each project
DeliveryThe distance to your addressA flat charge, confirmed with your address; always the last line
HST13% in OntarioShown on its own line, after the subtotal before HST

Installation figures are starting prices, and the calculator confirms them for your address. Our cost guide explains every line of an estimate, and the installation calculator prices your own rooms.

How much extra tile to order

Cuts use up tile, and diagonal and patterned layouts need more cuts, so your installer may suggest a larger allowance. The calculator offers an optional 10% allowance for cuts, which your installer confirms for your layout. Order everything at once, so the tiles are more likely to come from one batch. Check the batch numbers on the boxes, and keep a few spares. Our measuring guide shows how to work out boxes.

Choosing

What should I check before I buy tile?

Choose with the maker’s data in hand and full-size tiles in front of you.

Common buying mistakes

  • Choosing on looks alone, without checking that the tile is approved for floors.
  • Putting a polished tile where the floor gets wet, such as an entrance or a bathroom.
  • Planning large tiles without checking that the floor is flat enough for them.
  • Laying long tiles at a half offset when the maker allows only a third.
  • Counting on tile and grout to keep water away from the floor underneath.
  • Ordering only the measured area, or ordering a second batch later.
  • Coating ordinary glazed tile, or cleaning stone or cement grout with an acid.

Tile-shopping checklist

  • Its maker approves the tile for floors, and for outdoors or unheated rooms if you need that.
  • Porcelain: the certification mark, or water absorption of 0.5% or less on the data sheet.
  • Glazed tile: an abrasion (PEI) class that suits the room.
  • A slip rating that suits the room. For a floor that gets wet: an Interior Wet class, a wet DCOF of 0.42 or more, or the maker’s approval for wet floors.
  • The shade variation (V1 to V4), and several full-size pieces seen together.
  • Any side 15 inches or longer? Ask what the floor will need to be flat enough.
  • Rectified or calibrated edges, and the grout joint they need.
  • The grout type and colour, and whether its maker says to seal it.
  • For a wet area, the waterproofing system that will be used.
  • For in-floor heating, a heating system, setting materials and any membrane approved to work together.
  • Enough tile for cuts, plus spares from the same order.

Print this list (your browser’s Print command prints the guide without the menu) and bring it to the showroom.

Bring it to our Bolton showroom, where you can see full-size tiles and grout colours together, or call 905-872-7557.

How we checked

Sources we checked

The technical statements on this page follow these sources. Where products differ, the product’s own instructions and warranty decide. No paid standard was read; standards are cited from their published scopes and from the free summaries listed.

  1. Tile Council of North America (TCNA), Porcelain vs. Non-Porcelain, Porcelain Tile Certification, and its questions and answers on deflection, grout, epoxy grout, mortar, cleaning grout, cracked and hollow tile, crack isolation, lippage, movement joints, showers, exteriors, frost resistance, concrete curing, white residue, existing tile and tile over other flooring, checked 3 November 2026.
  2. ANSI A326.3-2021, dynamic coefficient of friction of hard surface flooring (the free copy published by TCNA), and TCNA’s DCOF questions, checked 3 November 2026.
  3. ASTM International, the published scopes of ASTM C373 (water absorption), C1027 (visible abrasion of glazed tile), C1243 (abrasion of unglazed tile) and C1026 (freeze and thaw), checked 3 November 2026.
  4. Ceramic Tile Education Foundation, articles on flat and level floors, flatness for large tile, offsets and grout joints, tile in wet areas, mortar coverage and tile over electric floor heating, checked 3 November 2026.
  5. Terrazzo, Tile and Marble Association of Canada (TTMAC), DCOF testing, checked 3 November 2026.
  6. Natural Stone Institute, care of natural stone, checked 3 November 2026.
  7. National Tile Contractors Association, TileLetter: sheet mosaics and tile tolerances, checked 3 November 2026.
  8. Condominium Authority of Ontario, Rules, and Canadian Condominium Institute (Toronto), Flooring, Vibration and In-Suite Renovations (2025), checked 2 November 2026.
  9. Health Canada, Chemical safety for do-it-yourself projects and renovations (asbestos in older homes), checked 2 November 2026.
  10. Manufacturers’ data sheets, installation instructions and care guides for tile, membranes, mortars, grouts and floor-heating cable (several brands), reviewed 3 November 2026.
Questions

Tile questions

Short answers. For your own rooms, call 905-872-7557 or visit the showroom.

What is the difference between ceramic and porcelain tile?

Porcelain is a kind of ceramic tile that soaks up very little water: 0.5% or less in a standard test (ASTM C373). Other ceramic tile soaks up more. Porcelain is denser and harder to cut; ceramic is easier to cut and set. Both work on floors when their maker approves them for floors.

How can I tell whether a tile is porcelain?

Look for the Porcelain Tile Certification Agency mark on the box or in the maker’s literature. Or look for water absorption of 0.5% or less on the maker’s data sheet. A missing mark means the tile was not certified, not that it is ceramic. Some tile sold as porcelain does not meet the standard.

Can wall tile be used on a floor?

Only if its maker approves it for floors. Some tiles are made for walls only, and for glazed tile, abrasion Class 0 means walls only. Our tile pages show the approved use, size by size.

Is porcelain tile slippery when wet?

It depends on the surface. Polished tile belongs where the floor stays dry, unless its maker says otherwise. For level indoor floors that get wet, look for an Interior Wet class, a wet DCOF of 0.42 or more, or the maker’s approval for wet floors. Many tiles show a European “R” slip class instead, so ask what it means for your room. No tile is slip-proof: water, oil, shoes and slopes all matter.

Does tile flooring need to be sealed?

Ordinary glazed tile does not, and its glaze should not be coated. Unglazed tile and polished porcelain sometimes do: follow the tile maker. For cement grout, follow the grout maker; epoxy grout is not normally sealed. Many natural stones need no sealer, and a sealer makes stone stain-resistant, not stain-proof.

Can tile crack over an uneven or bouncy floor?

Yes. Tile follows the floor under it. Humps and dips can leave tiles poorly supported, and a floor that bends can crack grout and tile. The floor is made flat and stiff enough before tiling. Cracks in concrete are assessed, and small ones can be bridged with a crack-isolation membrane where its maker allows.

Why do large tiles need a flatter floor?

A long, stiff tile cannot follow dips and humps, so its edges can stand up from its neighbours. The North American installation standard asks for a flatter floor once any side of a tile is 15 inches or longer. Then the floor may vary by no more than 1/8 inch over 10 feet, instead of 1/4 inch.

Does tile make a bathroom waterproof?

No. Porcelain soaks up very little water, but grout joints let water through. A bathroom floor can have a waterproofing membrane under the tile if you choose one. A shower is built as a sloped system, with a waterproofing membrane or a similar tested system behind the tile.

Can tile go over an existing floor?

Sometimes. It can go over well-bonded old tile with the right preparation, or over one well-attached layer of sheet vinyl without a cushion back. The mortar maker must approve it, and the floor underneath must be sound. Each layer raises the floor, so doorways and transitions are checked too.

How much extra tile should I buy?

Enough for cuts, plus a few spares. The calculator offers an optional 10% allowance for cuts, which your installer confirms for your layout. Diagonal and patterned layouts need more cuts, so your installer may suggest more. Buy it all at once so it is more likely to come from one batch, and keep the spares with their labels.

Can tile go over in-floor heating?

Usually. The heating system, the setting materials and any membrane must be used together as their makers instruct, and the tile’s maker must allow it. Electrical work must meet the electrical code. One heating-cable maker’s instructions we reviewed also call for the heat to stay off until the mortar has fully cured; follow your system’s instructions.

What is the one-third rule for tile?

It is the usual limit for staggering long tiles. Each row is offset by no more than a third of the tile’s length, unless the maker allows more. A half offset can make the slight bow of long tiles show as raised edges.

See tile in person

Compare full-size tiles, finishes and grout colours in our Bolton showroom, then book a free estimate to confirm your floor.