What is laminate flooring, and where does it work best?
Laminate is a plank floor with a wood-fibre core, a printed wood or stone design, and a clear, hard top layer. It suits dry rooms such as living rooms, bedrooms, halls and offices. Kitchens, entries and basements call for a product rated for those conditions. Products differ, so compare each one’s wear rating, water rating and warranty.
Homeowners choosing laminate for one room or a whole floor, and anyone planning it for a kitchen, basement or condo.
What is laminate flooring?
Laminate is a floor of planks built in layers: a core of wood fibres pressed together, a printed design of wood or stone, and a clear, hard layer on top that protects the design.
The planks click together at their edges. The finished floor “floats”: it rests on an underlay, a thin pad laid under the planks, and is held together by its own joints. That leaves it free to move a little as the seasons change.
Laminate and vinyl can look alike, but vinyl has a plastic core. Our laminate vs vinyl guide compares the two.
What laminate offers
Strengths- A printed wood or stone look, often with a textured surface
- A hard, clear top layer for everyday wear
- Planks that can be replaced one at a time
What to check first
Before you choose- Water: the core is wood-based, so check the water rating
- The subfloor, the surface under your floor: it must be flat and dry
- Concrete: a vapour barrier, a plastic sheet that slows moisture, goes under the floor
How is a laminate plank built?
A laminate plank has four layers. From the top: a clear wear layer, a decorative layer with the printed design, a core of high-density fibreboard (HDF), and a backer underneath.
| Layer | What it does |
|---|---|
| Wear layer | Protects the design from everyday wear. How well it resists wearing through is what the AC (abrasion class) rating grades. |
| Decorative layer | Gives the floor its look. Many surfaces are textured. On some, the texture follows the printed grain: this is called embossed in register (EIR). |
| HDF core | Gives the plank its strength and carries the click joints. It is wood-based, so it reacts to water and to the humidity in your home. |
| Backer | Usually melamine or another water-resistant material. It balances the plank so it stays flat. |
| Attached pad (some products) | Bonded to the back at the factory. It cushions the floor and reduces the sound of footsteps. |
What does a thicker laminate plank change?
A thicker plank resists impacts better, according to NALFA, the North American Laminate Flooring Association. The wear rating and the water rating are separate facts, so compare those as well.
Thickness is given in millimetres (mm). When you compare two products, ask whether each figure includes an attached pad.
| What you are comparing | What to look at |
|---|---|
| Impact resistance | Thickness. Thicker planks resist impacts, such as a dropped pot, better. |
| Wear from foot traffic | The surface. Compare the AC rating. |
| Water | The product’s design. Compare its water rating and warranty. |
| Sound and comfort | The underlay and the subfloor. See sound and comfort. |
| A flat subfloor | The instructions. Every thickness needs the flatness they ask for. |
| Floor height | Thickness. A thicker floor sits higher, which matters at doorways, stairs and where it meets another floor. |
Thinner planks can perform well with the right underlay, NALFA notes.
What do AC ratings and certifications tell me?
An AC rating grades one thing: how well the surface resists wearing through to the printed design. The classes run from AC1 to AC6 and come from the European laminate standard, EN 13329. Scratches, dents, water and fading are tested separately.
How the wear test works
In the abrasion test for laminate (ISO 24338), wheels covered in sandpaper turn on a sample of the floor. The lab counts the turns until the design starts to wear through. A higher class means the surface lasted longer in that test.
| Class | Typical retail description |
|---|---|
| AC1 and AC2 | Lighter household use, such as bedrooms and guest rooms |
| AC3 | General household use |
| AC4 | Busy households and general commercial floors |
| AC5 and AC6 | Heavier commercial floors; also chosen for the busiest rooms at home |
NALFA certification
NALFA runs its own certification. Independent labs test a product to the North American standard, ANSI/NALFA LF-01, in 14 categories, among them wear, impacts, fading in light, stains, heavy loads, moisture, and how well the planks keep their size and stay flat. The standard also asks for proof that the product meets formaldehyde emission limits. LF-01 uses its own tests, separate from AC classes.
Formaldehyde and the label
Laminate’s core is a wood-fibre board, so some buyers ask about formaldehyde. Canada’s Formaldehyde Emissions from Composite Wood Products Regulations (SOR/2021-148) apply to composite wood products that contain formaldehyde, including finished goods made with them. They set emission limits, and call for certification by an accredited third party and a label on the product or its packaging stating that it complies.
The AC rating, plus the scratch, stain and water information. Ask too whether the product has NALFA certification or a formaldehyde compliance label.
What does “waterproof laminate” mean?
It is a label some manufacturers use for laminate that holds water off its joints for a set time, such as 72 hours, under the warranty’s conditions. The core is still wood-based, so laminate is water-resistant: wipe up spills promptly on any laminate.
Some manufacturers label a laminate “waterproof”, others “water-resistant”. Look past the label to two facts: the number of hours, and the conditions in the warranty.
| Term | What it meant |
|---|---|
| A time limit | Water on the surface was held out of the joints for up to 72 hours in the two we reviewed. Wipe it up long before then. |
| Everyday spills | The warranty covered spills in normal use, in dry indoor rooms. |
| The planks only | The subfloor, the walls and the rest of the room were outside the warranty. |
| Sealed edges | Some instructions ask for sealant where the floor meets walls, cabinets and fixtures in rooms that get wet. |
| Concrete and basements | One warranty required a moisture barrier over concrete and below grade (below the ground level outside, as in a basement). |
| Exclusions | Flooding, leaking appliances or pipes, water under the floor, water pushed up from below, and mould. |
So the label covers the planks, for a set time. The edges of the room and the subfloor are outside that protection, and flooding is excluded.
Read the water warranty: the hours it allows, the rooms it covers, where it asks for sealed edges, and what it excludes. For rooms where water is part of daily life, compare with vinyl in our laminate vs vinyl guide.
Why does laminate need a gap around the edges?
The gap gives the floor room to move. Laminate’s wood-fibre core takes in and gives off moisture from the air, so the floor grows and shrinks slightly with the seasons. The planks are locked together, so the whole floor moves as one.
- The joints. The click joint is cut into the edges of the core. Water on the floor reaches the core first at the joints, which is why water warranties talk about them.
- Humidity. Relative humidity is how much moisture the air holds, as a share of the most it can hold. The laminate instructions we reviewed ask for 35% to 65% indoors, and some ask for that range for the life of the floor.
- Ontario seasons. Heated winter air is dry, and summer air is humid. A humidifier in winter, and air conditioning or a dehumidifier in summer, keep your home closer to that range.
- The expansion gap. A space is left at every wall and fixed object, such as door frames, posts and pipes. Baseboard or trim covers it. The instructions we reviewed ask for about 3/8 inch (10 mm).
- Long rooms. A longer floor moves more in total. One set of instructions adds 1/16 inch to the gap for every 5 feet beyond a 50-foot run.
- Door frames. The bottoms of door frames are trimmed, so the floor and its gap slide underneath.
Which underlay does laminate need?
Laminate goes over an underlay: a pad attached to the planks at the factory, or a separate underlay rolled out first. Over concrete, the instructions also call for a vapour barrier. An attached pad counts as one only when the product says so.
Attached pad
Bonded to the back of each plank. It cushions the floor and reduces the sound of footsteps. Check the instructions before adding anything under it: on some products, a second pad voids the warranty.
Separate underlay
Rolled out before the planks go down. Choose one the plank’s instructions approve. One set we reviewed allows a separate underlay up to 1/8 inch (about 3 mm) thick.
Vapour barrier
A plastic sheet that slows moisture rising from concrete. The instructions we reviewed ask for polyethylene 6 to 8 mil thick, about 0.15 to 0.2 mm (a mil is a thousandth of an inch). Some underlays have one built in; use one where the plank’s instructions accept it.
An underlay follows the shape of the floor under it. Low spots are filled and high spots ground down first, so the joints are supported along their whole length.
How will laminate sound and feel underfoot?
Laminate is a firm floor. The underlay and the subfloor under it shape how it sounds, in the room and in the room below.
- In the room. This is the sound of footsteps on the floor itself; labs measure it with a standard method (EN 16205). An acoustic underlay, or a pad attached at the factory, reduces it. Rugs and felt pads under furniture help too.
- In the room below. This is footstep noise that travels down through the floor. Labs measure how much a floor covering reduces it on a standard concrete floor (ASTM E2179). A figure measured on concrete does not carry over directly to a wood-framed floor.
- Comfort. Laminate feels firm underfoot. Rugs soften the places where you stand most, such as the kitchen sink.
Condos
In an Ontario condo, the corporation’s declaration, by-laws and rules decide what you may install. Many buildings set their own flooring rules, such as approval before work starts and an underlay that meets a stated sound rating, often given as IIC (impact insulation class). Ask the management office for the rule in writing before you choose a floor.
A sound rating describes the whole floor and ceiling together, so the building’s rule decides which test and which figure count.
What does the subfloor need before laminate goes down?
A laminate floor needs a base that is firm, flat, clean and dry. Each product’s installation instructions set the exact limits, and the subfloor is checked against them first.
| Requirement | What to expect |
|---|---|
| Flat | Often within 3/16 inch over 10 feet (about 5 mm over 3 m). Some products ask for 1/8 inch over 6 feet. Low spots are filled and high spots ground down. |
| Firm | A wood subfloor that moves or squeaks is fastened down first. |
| Dry | Concrete is tested for moisture with a standard test (ASTM F2170 or ASTM F1869) and must meet the product’s limit. New concrete needs at least 60 to 90 days to dry, in the guidance we reviewed. |
| Clean | Old carpet and its pad come up, and the surface is cleared and swept. |
| Acclimation | Letting the boxes adjust to the room. One set of instructions asks for at least 48 hours in the room, in unopened boxes. Another needs no wait when the boxes were already kept at room conditions. |
| Expansion gap | About 3/8 inch (10 mm) at the walls and fixed objects, and more in very long rooms. |
Installation is completed by The Flooring Mart’s own in-house installation teams. We do not use subcontractors, which is why we can stand behind our flooring installation work with a 2-year limited workmanship warranty. We check your subfloor when we measure, so the preparation it needs is part of your estimate from the start. Read more about subfloor preparation and flooring installation.
Homes built before 1990 may have asbestos in building materials, old floor tiles among them. Health Canada advises a professional test before renovating, and a qualified removal specialist if asbestos is found.
Which rooms suit laminate?
Laminate suits dry rooms: living and dining rooms, bedrooms, halls and home offices. Kitchens, entries and basements call for a product rated for the conditions. Bathrooms and laundry rooms need a product its manufacturer approves for that room.
| Room | A good fit when | Check first |
|---|---|---|
| Living and dining rooms | You like the look: any laminate suits a dry room | Strong sun: some products are tested and warranted for fading. Felt pads under furniture. |
| Bedrooms | You like the look: any laminate suits a bedroom | Sound: an acoustic underlay when the bedroom is above a lived-in room. |
| Halls and entries | The product has a higher AC rating and a water rating | Grit, salt and wet boots: mats inside and outside the door. |
| Kitchens | The product has a water rating, and its warranty covers kitchens | Wipe spills promptly. The water warranty we reviewed excludes leaking appliances. |
| Basements | The manufacturer allows below-grade use | A moisture test, a vapour barrier, and a dry, climate-controlled space. Some products exclude rooms with a floor drain or a sump pump. |
| Bathrooms | The manufacturer approves the product for bathrooms | Sealed edges, and water wiped up at once. |
| Laundry rooms | The manufacturer approves the product for the room | Washer leaks and floor drains: check the warranty and the instructions. |
| Stairs | Matching stair nosing is available for the product | Each staircase is measured and priced on site. |
| Condos | The building allows it | The building’s rules and underlay rating, in writing. |
| Cottages and sunrooms | The product is approved for the room’s conditions | Some instructions ask for a climate-controlled home, kept within a set temperature and humidity range all year. |
| Heated floors | The manufacturer approves the product over in-floor heating | The maximum temperature: 27 to 29 °C in the instructions we reviewed. |
To weigh laminate against other floors, the guide to choosing a floor compares five types, and the Flooring Match Guide suggests floors for your rooms.
How do I look after a laminate floor?
Keep grit off the floor, clean with a damp mop and the cleaner your product’s care guide names, and wipe up water promptly. Felt pads, doormats and trimmed pet nails protect the surface.
Cleaning
- Sweep, dust-mop or vacuum on a hard-floor setting. Grit wears the surface like fine sandpaper.
- Damp-mop with the cleaner the care guide names. Wring the mop well, so it feels almost dry.
- Steam depends on the product. Many manufacturers advise against steam mops, and some products are approved for them. Use one only if your product’s care guide allows it.
- Keep a note of the cleaners you use. One warranty we reviewed asks for it.
Scratches, dents and fading
- Scratches. The clear top layer protects the design. Scratch resistance is tested separately from the AC rating, so ask about it when you compare products.
- Dents. Put felt pads or wide floor protectors under furniture legs, and lift heavy pieces to move them.
- Fading. Some products are tested and warranted for fading from sunlight. Blinds and curtains soften strong sun on any floor.
Repairs
- Small chips and scratches can be filled with a colour-matched laminate repair kit.
- A plank with a deep mark, or one that has swollen, is cut out and replaced. A plank from your own spare box matches best.
- Hardwood is sanded and refinished; laminate is renewed by replacing planks, because its surface is a printed design under a thin clear layer.
- Keep the receipt and a few spare planks. One warranty we reviewed asks owners to keep five.
The measuring guide explains how to keep spare boxes in good condition.
How do I compare laminate products and plan the total cost?
Compare products on the facts that differ between them: the wear rating, the water rating, the thickness, the pad and the warranty. Then plan the whole project, because the total covers the work around the floor as well as the planks.
| Compare | What to look for |
|---|---|
| Wear | The AC rating, and scratch and stain information where the product publishes it |
| Water | The rating in hours, the rooms its warranty covers, and its conditions |
| Thickness | Impact resistance and floor height, and whether the figure includes a pad |
| Pad | Attached or separate, and what the instructions allow over concrete |
| Look | Plank width and length, the surface texture, and how often the printed pattern repeats |
| Labels | NALFA certification and a formaldehyde compliance label |
| Warranty | What it covers, what it asks of you, and for how long |
What shapes the total cost
- The product: its wear rating, water rating, thickness, plank size and surface. Our laminate floors run from $1.99 to $3.29 per sq ft for material (our catalogue, 2 November 2026).
- The coverage you buy: flooring comes in full boxes, and installation is priced on the coverage of the boxes you buy. Click installation starts at $2.25 per sq ft, before HST; a project under 400 sq ft has one all-inclusive installation price instead, from $1,250.00.
- The layout: herringbone and chevron take more labour and more cutting than straight rows.
- Taking up and hauling away the old floor.
- Subfloor preparation: levelling, fastening and moisture protection.
- The underlay and, over concrete, the vapour barrier.
- Trim: baseboard, shoe moulding, transitions and stair nosing.
- Stairs, priced for each staircase.
- Delivery, and HST on the subtotal.
Each laminate’s price is on its product page. The flooring cost guide explains every line with worked examples, and the installation calculator prices your rooms with the product you choose.
The preparation, the vapour barrier and the underlay the product’s instructions ask for. The floor’s warranty depends on them.
What should I check before I buy laminate?
Run through this list before you choose. Each point is explained above.
Before you choose laminate
- The AC rating, matched to how busy each room is
- The water rating in hours, and what its warranty covers and excludes
- The rooms: any kitchen, entry, basement, bathroom or laundry room?
- The subfloor: concrete needs a moisture test and a vapour barrier
- Attached pad or separate underlay, and what the instructions allow
- Your condo’s rules for flooring and underlay, in writing
- In-floor heating: the product’s approval and maximum temperature
- Flatness and preparation, checked before installation
- Time for acclimation in your schedule
- Trim, transitions and stairs
- The receipt and some spare planks, kept for repairs and the warranty
- A large sample, seen in your own light
Print this page with your browser’s Print command; it prints as a clean checklist.
What should I do next?
Pick a few products, price your rooms, then confirm the details with a free measurement.
- Browse our laminate collection and note two or three products you like.
- Price your rooms in the installation calculator.
- Book a free in-home measurement through the calculator, or call 905-872-7557.
- Visit the showroom at 55 Healey Rd, Unit 2, Bolton, ON L7E 5A2 (Mon–Fri 9:30 AM–8 PM; Sat 10 AM–7 PM; Sun 11 AM–6 PM) to compare samples side by side.
Sources we checked
The technical statements on this page follow these sources. Where products differ, the product’s own instructions and warranty decide.
- North American Laminate Flooring Association (NALFA), What is laminate?, Laminate Flooring FAQs and Product Certification (ANSI/NALFA LF-01), checked 2 November 2026.
- American National Standards Institute, member update on NALFA’s white paper on wear resistance and AC ratings (4 January 2023), checked 2 November 2026.
- Standards, from their published scopes: EN 13329:2023 (laminate floor coverings, including AC classes), ISO 24338 (laminate abrasion test), EN 16094 (scratch tests), EN 16205 (walking sound), ASTM E2179 (impact sound), ASTM F2170 and ASTM F1869 (moisture in concrete); NIST SP 811 for the mil (exactly 0.0254 mm). Checked 2 November 2026.
- Justice Laws Website, Formaldehyde Emissions from Composite Wood Products Regulations (SOR/2021-148), current to 30 September 2026, checked 2 November 2026.
- Health Canada, Chemical safety for do-it-yourself (DIY) projects and renovations (asbestos in older homes), checked 2 November 2026.
- Condominium Authority of Ontario, Rules, and Canadian Condominium Institute (Toronto), Flooring, Vibration and In-Suite Renovations (2025), checked 2 November 2026.
- Manufacturers’ installation instructions, water warranties and care guides for laminate (flatness, concrete moisture, acclimation, expansion gaps, underlay and vapour barriers, in-floor heating, steam cleaning, repairs; several brands), reviewed 2 November 2026.
